Wednesday, 31 August 2016

REVIVE YOUR HARD BRICK YUREKA AND YUREKA PLUS NO SAHARA ERROR AT ALL, WORKING METHOD FOR EVEN MOST HARD BRICKED SNAPDRAGONS

Bricked our loving YUREKA. Don't worry at all you are at the right place.


 Just follow these steps and your yureka will be live again.

Note: I shall not be responsible in case you fire your yureka by mixing any other method with this, I highly recommend that you carefully follow each and every step to get success.  
You will need :

1. Dead/Hard bricked Yureka

2. 32GB Memory Card

4. Data Balance nearly 1GB

5. Little Brain and a Cup of Coffey for Relaxing and enjoying your live yureka again.


Download:

1. Full emmc backup of yureka from here
http://shink.in/1hj6V

2. WIN32DISK Imager from here
http://shink.in/EMj7n

3. Fastboot Image from here
http://shink.in/diZq5

4. ADB Driver
http://shink.in/XtrJM
http://shink.in/bIs0j

5. List of ADB Qualcomm command Set
http://shink.in/Nuq5d

Now follow thease steps:

1. Extract EMMC Backup file to your computer

2. Install WIN32Imager

3. Connect your SD Card via SD Card reader

4. Format SD Card in FAT Format


5. Open WIN32Disk Imager and Select that emmc backup file which you have extracted.
6. Select the SD CARD Drive from Drop Down list

7. Click Write
Wait till write process finshes

8.Now Remove your Yureka's Battery

9. Insert SD card and press and hold vol. UP and connect usb (Enter into Fastboot mode)

10. Install Fastboot drivers

11. Extract the fastboot zip into adb folder given in fastboot tool

12. Press Ctrl. + Shift + Right Click in adb folder and select " Open Command Prompt here"

13. follow these list of commands and get success.

Donate me a cup of Coffey if I helped you so that i can be awake to work for you guys.
SBI A/c 31558110394   IFSC: SBIN0012470
your help will be appreciated 

Need any more help,
Comment your quries or vist me at www.pitssco.in or support@pitssco.in

Posted by at

6 comments:

  1. Unknown31 August 2016 at 18:25

    THAAANKS BRO....

    ReplyDelete
  2. Saurabh B13 September 2016 at 06:51

    hello there,
    i have tried the same method but my phone is not getting into fastboot mode....
    just red light glows and it keeps vibrating countinuously.
    what should i do ?

    ReplyDelete
  3. Unknown13 September 2016 at 16:10

    Does your phone getting detected as QUSB_Bulk or QUALCOMM PORT 9008 in devices.
    Did you followed all steps correctly.
    Note: You should not open memory card when writing process finish.
    and Dont use any phone as card reader.
    Use a Cardreader only

    Need instant help
    write me at support@pitssco.in

    ReplyDelete
  4. Saurabh B15 September 2016 at 02:18

    Yes at initial state it is getting detected as QUALCOMM PORT 9008 mode
    and i have followed all the steps correctly. I have used card reader only.
    And one more thing i have already revived an another yureka with same procedure that was successful.
    but this device is not responding properly at all

    ReplyDelete
  5. Unknown16 September 2016 at 15:24

    have you tried qpest method?

    ReplyDelete
  6. Saurabh B17 September 2016 at 11:48

    No. But i would like to try it.
    Can you please direct to the actuak method?

    ReplyDelete

Thanks for writing. We will review your comment for feedback

Subscribe to: Post Comments (Atom)